Contents

Russian Engineering Research

---

Vol. 44, No. 9, 2024

---

Automation of Power Supply Control of an Industrial Enterprise

A. N. Karelin, V. A. Matigorov, N. E. Karelin, and E. N. Karelin p. 1235  abstract

Improving the Reliability of Pipe End Joints Using Shape Memory

I. N. Kravchenko, D. U. Khas’yanova, D. I. Petrovskiy, E. I. Cherkasova, D. A. Pupkova, and P. V. Chumakov p. 1240  abstract

Contact Deformation of Gear Teeth

F. G. Nakhatakyan, and D. F. Nakhatakyan p. 1244  abstract

Characteristics of a Vortex Hydropneumatic Diode with a Rotating Impeller

S. Yu. Kaygorodov p. 1248  abstract

Experimental Study of the Impact Action of Grates on Raw Cotton in Cotton Gins for Large Foreign Matter

R. Kh. Rosulov p. 1252  abstract

Control of Power Distribution in the Transmission of an Integral Tractor

R. Yu. Dobretsov, K. V. Tcheremisin, S. A. Voinash, V. A. Sokolova, S. A. Partko, and R. R. Zagidullin p. 1257  abstract

Investigation of the Permeability Function of the Contact of the Wedged Edge of a Metal Seal with a Flange under External Loads

A. A. Boikov, and O. A. Rod p. 1263  abstract

Factors Affecting the Wear Rate in Frictional Systems

M. A. Mel’nik p. 1270  abstract

Stress–Strain State in the Surface Layer during Shot Hardening

I. G. Shin, R. Kh. Maksudov, M. R. Muminov, and S. R. Nazarov p. 1275  abstract

Design of Metal–Polymer Tribological Systems Containing Fluoroplastic

V. A. Kokhanovskiy, and N. V. Nikhotina p. 1280  abstract

Parameter Calculation in Constrained Extrusion of Unequal Channels without Hardening

A. L. Vorontsov p. 1283  abstract

Development of Automation Methods to Design Special Welding Fixture Layouts

I. I. Krasnokutsky, and A. Yu. Panov p. 1287  abstract

Band Matrices, Markov Chains, and the Reliability of Engineering Systems

N. E. Zubov, and V. N. Ryabchenko p. 1294  abstract

X-Ray Structural Analysis of Iron-Based Powder

S. A. Jafarova p. 1303  abstract

Power of Built-In Heater at the Cooling Stage in Welding Polyethylene Pipe at Low Ambient Temperatures

N. P. Starostin, and O. A. Ammosova p. 1306  abstract

Strength and Crack Resistance of Hard Alloys and Coatings at Fracture: Atomic Dislocation Analysis

Yu. G. Kabaldin, and A. A. Bashkov p. 1311  abstract

Investigation of the Effect of Milling Cutter Tooth Spacing and Milling Mode Features on the Process of Machining Polycarbonate Workpieces Using Ultrasonic Vibrations

A. N. Unyanin, and I. Z. Dimukhametov p. 1317  abstract

Contact Zone and Tool Wear in Belt Grinding

D. I. Volkov, A. A. Koryazhkin, A. V. Kurochkin, A. N. Sutyagin, and A. N. Rykunov p. 1323  abstract

Formation of Workpiece–Tool Contact Zone in Belt Grinding of Blades for Gas Turbine Engines

D. I. Volkov, A. A. Koryazhkin, A. V. Kurochkin, A. N. Sutyagin, and A. N. Rykunov p. 1329  abstract

Analysis and Optimization of the Right Pillar in a Glue Roller Drive Mechanism

S. I. Boriskin, S. A. Efanov, and V. N. Kechemaikin p. 1334  abstract

System Tools for Quality Assurance for Electric Vehicle Design

I. A. Belyaeva, V. N. Kozlovskii, E. V. Strizhakova, and A. S. Klentak p. 1338  abstract

Overview of Key Regulatory Documents Defining Quality Requirements to the Design of Automotive Gear Motors

O. D. Ibragimov, V. N. Kozlovskii, A. P. Novikova, and D. A. Demoretskii p. 1341  abstract

Software Tool Based on Dimensional Chains for Determining Stator and Rotor Misalignment in an Automobile Generator

A. S. Saksonov, V. N. Kozlovskii, U. V. Brachunova, and D. I. Panyukov p. 1344  abstract

Development of a Typology of Consumers of New Cars in the Context of Quality Assurance Issues

A. S. Klentak, V. N. Kozlovsky, and D. S. Gordienko p. 1347  abstract

Analysis of the Automotive Market Considering the Quality of Products Required by Consumers

A. S. Klentak, V. N. Kozlovsky, and D. V. Aydarov p. 1352  abstract

Сompilation of a Set of Informative Features for Neural Network-Based Determination of Minimum Vibration of Cutting Tools

V. P. Lapshin, I. A. Turkin, and I. O. Dudinov p. 1356  abstract

Business Processes of an Enterprise in Maximizing the Utilization of Available Production Equipment

L. L. Khoroshko, and P. M. Kuznetsov p. 1363  abstract

Thermophysical Study of Liquid Solutions

S. Yu. Poberezhskii p. 1367  abstract

Novel Tools for Monitoring Process Quality: Detection of Anomalies in Digital Data on Content Consumption Using the DBSCAN Clustering Method

V. G. Mosin, V. N. Kozlovskii, and M. V. Nenashev p. 1370  abstract

Methodological Approach to Development of a Production Program Based on Optimization of Financial Resources

O. V. Nesterov, N. S. Efimova, and E. V. Surkova p. 1375  abstract

---