Contents

Russian Engineering Research

Vol. 36, No. 9, 2016

A simultaneous English language translation of this journal is available from Pleiades Publishing, Ltd.
Distributed worldwide by Springer. Russian Engineering Research ISSN 1068-798X.

Synthesis of Roller Screws

V. V. Morozov, A. V. Zhdanov and A. B. Kosterin p. 703  abstract

Plates in Hydraulic Presses with Ohmic Heaters

E. N. Malygin, S. V. Karpushkin, A. O. Glebov and S. V. Karpov p. 708  abstract

Automated Machining of Turbine Blades

V. A. Poletaev, E. V. Tsvetkov p. 713  abstract

Vibrational Machining with Torsional Spindle Vibrations

A. Ya. Ryzvanovich, V. A. Generalov and V. V. Kapralov p. 717  abstract

Stress and Strain Concentration in Weld-Joint Flaws

K. P. Manzhula and A. Yu. Shlepetinskii p. 722  abstract

Thermal Distribution in the PTFE–Steel Frictional Pair

E. B. Sedakova and Yu. P. Kozyrev p. 727  abstract

Burnishing with Wear-Resistant Mineral–Ceramic and Hard-Alloy Indenters

V. N. Gadalov, A. E. Gvozdev, D. N. Romanenko, I. V. Vornacheva and S. V. Kovalev p. 731  abstract

Dynamic Stability of Band Saw Machines

L. V. Kremleva, V. I. Malygin and N. V. Lobanov p. 735  abstract

Behavior of Heat-Resistant Alloys and Titanium Alloys on Cutting

G. D. Petukhov and V. F. Makarov p. 741  abstract

Automated Production System for Reagents Used in Water and Wastewater Processing

E. N. Arakcheev, V. E. Brunman, M. V. Brunman, A. N. Volkov, V. A. D’yachenko, A. V. Kochetkov and A. P. Petkova p. 745  abstract

Automated 3D Modeling of Working Turbine Blades

A. I. Ryazanov p. 751  abstract

Automated Management of Manufacturing Orders

K. S. Kul’ga p. 755  abstract

Improving Tool Life and Machining Precision in Band Saws

A. E. Litvinov p. 760  abstract

Precision and Efficiency of Metal-Cutting Machines

V. V. Bushuev, A. P. Kuznetsov, F. S. Sabirov, V. S. Khomyakov and V. V. Molodtsov p. 762  abstract

Control Loops of a Supply Servo Drive

V. V. Bushuev, S. V. Evstafieva and V. V. Molodtsov p. 774  abstract

Recursive Model of the Blunting of an Abrasive Grain

D. V. Ardashev p. 781  abstract

Parametric Modeling of Ball End Mills

E. A. Ryabov, S. Yu. Yurasov and O. I. Yurasova p. 784  abstract

Influence of the Wire EDM Conditions on the Cut Width

T. R. Ablyaz and R. V. Lesnikov p. 786  abstract

Optimizing the High-Speed Drilling of Small-Diameter Holes by Core Flat Drills

Yu. I. Myasnikov and D. Yu. Pimenov p. 788  abstract

Reliability in Gear Shaping

V. A. Grechishnikov, R. M. Khusainov, S. Yu. Yurasov and R. R. Khaziev p. 791  abstract