Contents
Russian Engineering Research

Vol. 28, No. 8, 2008

Simultaneous English language translation of the journal is available from Allerton Press, Inc.
Distributed worldwide by Springer. Russian Engineering Research ISSN 1068-798X.

Calculating the Wear Resistance of Metals in Frictional Pairs 3. Calculating the Wear Rate
of Steel in Roller Pairs with Rolling Friction and Slip

A. M. Ryakhovskii p. 733  abstract

Influence of Wear of a Roller Drive Chain on Transmission Fitness

S. A. Metil’kov and V. V. Yunin p. 741  abstract

Turbine Vibration with a Pulsed Kinematic Perturbation

V. F. Shatokhin p. 746  abstract

Influence of Coiling on the Carrying Capacity of Vertical Tanks

A. V. Didkovskii, Ya. M. Klebanov, and A. N. Davydov p. 754  abstract

Dynamic Operational Stability of Measuring and Control Systems Based
on Vibrocontact Measurements

G. M. Trompet and A. Ya. Krasil’nikov p. 759  abstract

Semiperiodic Screening of a Rotating Plane Wing

S. A. Gerasimov p. 762  abstract

Contact Friction in the Deformation Zone during Ultrasonic Surface Plastic Deformation

T. M. Gavrilova p. 764  abstract

Ensuring the Reliability of Liquid-Friction Bearings for Rolling Mills

A. A. Zyuzin and B. N. Kaz’min p. 769  abstract

Cutting of Corrosion-Resistant Steel Using a Tool with a Short Front Surface

A. I. Sedel’nikov p. 775  abstract

Milling Complex Surfaces on a Numerically Controlled Machine Tool

N. V. Kolesov and S. Yu. Yurin p. 779  abstract

Brittle Tensosensitive Coatings for Determining the Stress–Strain State
of Parts and Structures

A. N. Salin and A. I. Dolinnyi p. 782  abstract

Development of a New Theory of Cutting 8. Chip-Breaker Design

A. L. Vorontsov, N. M. Sultan-Zade, and A. Yu. Albagachiev p. 786  abstract

Applying Ribbing to Plates

E. Yu. Polikarpov p. 793  abstract

Bauschinger Effect in Complex Machining Methods

A. V. Shchedrin, V. V. Ul’yanov, V. M. Skoromnov, and A. A. Bekaev p. 797  abstract

Russia’s Leading Machine-Tool Manufacturer p. 800  abstract

Minimizing the Space Occupied by Multicoordinate Gear-Cutting Machine Tools
for the Manufacture of Conical and Hypoid Transmissions

L. I. Sheiko and S. Ya. Prikazchikov p. 801  abstract

Self-Adjusting Guide Pieces Based on a Rigid Center

V. B. Il’itskii and V. V. Moiseev p. 804  abstract

End Machining of Teeth by a Single-Turn Worm Mill

N. A. Chemborisov and A. G. Kondrashov p. 809  abstract

Selecting Rational Geometric Parameters of a Disk Mill in Machining
High-Temperature Nickel Powder Alloys

A. V. Kovalevskii p. 812  abstract

Margin in Sharpening Helical Channels of Tool

A. D. Balandin and B. D. Danilenko p. 814  abstract

X-Ray Microspectral Analysis of Ceramic Binder and Its Contact Zones
with Silicon-Carbide Grains

I. V. Nadeeva and N. V. Nosenko p. 816  abstract

Automating the Design of Technological Processes

S. A. Volkov p. 821  abstract

Functional–Technological Approach to Selection Criteria for Equipment

A. V. Mukhin and V. V. Petrov p. 825  abstract

Forces and Contact Temperature in Plane End Grinding by Composite Wheels

S. M. Mikhailin p. 829  abstract

Ensuring Surface-Layer Quality in Plane Grinding of High-Temperature Nickel Alloys

V. F. Bez”yazychnyi, B. M. Drapkin^†, and M. A. Prokof’ev p. 833  abstract

More Efficient Deep Grinding

O. G. Bykadorova and V. M. Shumyacher p. 836  abstract

Improving the Structure of an Abrasive Tool without Binder

Yu. N. Polyanchikov, M. Yu. Polyanchikova, A. A. Emel’yanenko, and A. L. Plotnikov p. 838  abstract

Pleiades Publishing home page | journal home page | top

If you have any problems with this server, contact webmaster.