Contents

Russian Engineering Research

Vol. 44, No. 7, 2024

Methodology for Design of Magnetorheological Dampers to Protect Wires of Overhead Power Lines

A. I. Ermolaev, V. I. Erofeev, and I. V. Tishin p. 895  abstract

Solution for the Operational Repositioning of Saw Modules when Automating Sawmill Equipment

M. A. Blokhin, I. I. Dymchakov, A. P. Shein, and D. D. Emel’yanov p. 904  abstract

Finishing and Hardening of Cycloidal Helical Surfaces by Surface Plastic Deformation with Programmed Tool Control

I. O. Zenin, P. D. Akulinichev, M. A. Al’bov, and A. A. Goncharov p. 908  abstract

Determination of Indicators for Optimal Selection of Technological Operations when Repairing Parts of Aircraft Gas Turbine Engines

V. F. Bezyazychniy, A. V. Smirnov, and S. S. Kalugin p. 912  abstract

Calculation of Deep Contact Endurance of Transmission Gears

S. P. Rudenko, S. G. Sandomirskii, and A. L. Val’ko p. 917  abstract

Separation of Impurities from Raw Cotton

A. M. Erdonov, R. Kh. Rasulov, and Kh. A. Akhmedov p. 924  abstract

Determination of the Fit of a Chain Coupling on a Gearbox Shaft

D. A. Pupkova p. 928  abstract

Design Method for Finishing by Free Abrasive

P. D. Akulinichev, A. A. Goncharov, M. A. Al’bov, and I. O. Zenin p. 931  abstract

Influence of Key Parameters of Laser Peen Forming on Plate Bending

G. Zh. Sakhvadze p. 935  abstract

Influence of the Substrate Thickness in Elastoplastic Deformation of a Microprofile under Orthogonal Constrained Loading

N. V. Vulykh p. 940  abstract

Parameter Calculation in Constrained Extrusion of Unequal Channels: Determining the Stages and Parameters of the Process

A. L. Vorontsov p. 946  abstract

Electrochemical Machining of Additively Manufactured Products Made of Ti–6Al–4V Alloy

E. V. Krasnova, Yu. A. Morgunov, B. P. Saushkin, I. A. Slyusar’, and S. A. Smeyan p. 951  abstract

Mechanical Properties of Stainless Steel Components during Additive Manufacturing (SLM and WAAM)

Yu. G. Kabaldin, and V. V. Vysokolov p. 961  abstract

Improving Tool Performance in Turning Hard Stainless Steels

B. Ya. Mokritskiy, A. V. Kosmynin, and A. V. Kirichek p. 965  abstract

Methodology for Design and Research of Vibration Stability of Cylindrical Milling Cutters with Nonuniform Tooth Inclination Angle

Ya. L. Liberman, V. S. Ovsiannikova, and L. N. Gorbunova p. 970  abstract

Influence of 3D Printing Process Parameters on Mechanical Properties of ABS Plastic Samples Fabricated by Material Extrusion

A. A. Shileyko, A. A. Kutin, and V. V. Pirogov p. 975  abstract

Russian Precision Finishing Machines

K. R. Muratov, E. A. Gashev, T. R. Ablyaz, and D. P. Davydov p. 984  abstract

Controlled Shaping of Precision External Cylindrical Surfaces

K. R. Muratov, D. P. Davydov, E. A. Gashev, and T. R. Ablyaz p. 987  abstract

Stability Assessment in Milling Aircraft Engine Components

A. V. Martynyuk, V. V. Kuritsyna, and M. V. Siluyanova p. 990  abstract

Influence of Unilateral and Bilateral Coolant Supply on the Thermal Characteristics of a Plate–Fin Heat Exchanger

A. V. Vikulin, and V. A. Zemlyanaya p. 994  abstract

Fabrication of Titanium Alloy-Based Composite Materials from Bimodal Powder Mixtures Ti–6Al–4V–(Cu–Al) by Direct Selective Laser Melting

Yu. I. Gordeev, E. V. Gerasimov, G. M. Zeer, E. G. Zelenkova, E. V. Moskvichev, and V. B. Yasinksii p. 998  abstract

Plasma Metallization for Additive Manufacturing of Workpieces Made of 308 LSi Steel

Yu. D. Shchitsyn, D. S. Belinin, S. D. Neulybin, K. P. Karunakaran, T. V. Ol’shanskaya, A. V. Kazantsev, and S. G. Nikulina p. 1005  abstract

Machining of Resurfaced Gas-Turbine Engine Components: Precision of Wire-Cut Electrical Discharge Machining

D. A. Borisov, T. R. Ablyaz, E. S. Shlykov, K. R. Muratov, and E. V. Plotnikov p. 1011  abstract

Factors Affecting the Cut Width in the Wire-Cut Electrical Discharge Machining of VV751P Heat-Resistant Nickel Alloy

V. T. Khairulin, T. R. Ablyaz, E. S. Shlykov, V. B. Blokhin, and K. R. Muratov p. 1014  abstract

Improving the Productivity of Copy-Piercing Electrical Discharge Machining by Additive Manufacturing of Tool Electrodes

R. M. Aliev, T. R. Ablyaz, E. S. Shlykov, K. R. Muratov, and V. B. Blokhin p. 1017  abstract

Microstructure in Surface Layer of Heat-Resistant Materials after Electrical Discharge Machining

T. R. Ablyaz, E. S. Shlykov, I. V. Osinnikov, K. R. Muratov, and V. T. Khairulin p. 1020  abstract

Improved Monitoring of the Adhesive Strength of Coatings

A. A. Snezhko, A. A. Fadeev, E. A. Zhirnova, N. V. Zakharova, and E. A. Karelina p. 1023  abstract

Analysis and Improvement of the Risk Assessment System Based on the Risk Priority Number

D. I. Panyukov, M. V. Nenashev, V. N. Kozlovskii, and D. V. Aidarov p. 1026  abstract

Improvement of the Risk Assessment System Based on the FMEA Action Priority Method

D. I. Panyukov, M. V. Nenashev, V. N. Kozlovskii, and D. V. Aidarov p. 1030  abstract

Development and Implementation of Statistical Tools for Assessing Risks of Insufficient Quality of Automotive Components

V. N. Kozlovskii, D. I. Panyukov, D. V. Aidarov, and A. V. Kritskii p. 1035  abstract

Substantiation and Development of Statistical Parameters for Assessing Risks of Insufficient Quality of Automotive Components

V. N. Kozlovskii, D. I. Panyukov, D. V. Aidarov, and A. V. Kritskii p. 1040  abstract

Import Substitution of Automated Project Management Systems for Software Development at High-Tech Enterprises

N. S. Efimova, O. V. Nesterov, and A. N. Novikov p. 1044  abstract

Management of High-Tech Companies in Conditions of Import Substitution

S. E. Pyatovsky, N. S. Efimova, and E. V. Surkova p. 1050  abstract

Digital Transformation as an Effective Development Strategy for Industrial Enterprises

N. V. Arsen’eva, L. M. Putyatina, V. V. Kolosova, and G. V. Tikhonov p. 1054  abstract

Features of the Functioning of a Distributed System by Stages of the Life Cycle of a Technical System

M. V. Siluyanova, M. N. Kaloshina, and E. V. Dianova p. 1058  abstract

Development of an Import Substitution Mechanism at Moscow Aircraft Manufacturers

A. I. Tikhonov, N. V. Prosvirina, and M. V. Siluyanova p. 1064  abstract

Organization of Project Management on the Basis of Reverse Modeling

Yu. G. Sledkov, L. L. Khoroshko, and P. M. Kuznetsov p. 1068  abstract

Justification of Options for R&D Result Commercialization Considering the Principles of Financial Model Formation

M. N. Kaloshina, and T. Yu. Nikolenko p. 1071  abstract

Assessment of Project Risks in the Russian Economy

G. V. Tikhonov p. 1075  abstract

Erratum

Erratum to: Mechanical Properties of Structural Steel after Diamond Burnishing

G. R. Hamzayeva p. 1079  abstract