Contents

Russian Engineering Research

---

Vol. 36, No. 7, 2016

A simultaneous English language translation of this journal is available from Pleiades Publishing, Ltd.
Distributed worldwide by Springer. Russian Engineering Research ISSN 1068-798X.

---

Harmonic Analysis of the Kinematic Error in a Planetary Roller Screw

I. M. Mamaev, V. V. Morozov, O. V. Fedotov and V. N. Filimonov p. 515  abstract

Non-destructive Testing of Residual Stresses by Magnetic Methods under Conditions of Simple Stressing

M. S. Mahalov and V. Yu. Blumenstein p. 520  abstract

Manufacture of Mandrels for the Production of Composite Components by Coiling

A. S. Zuev p. 526  abstract

Properties of Thick Galvanic Steel Coatings

Yu. R. Kopylov p. 528  abstract

Stress Concentration at the Edge of a Circular Hole with Unilateral Annular Reinforcement

V. F. Kozhevnikov and V. V. Firsanov p. 532  abstract

Stress–Strain State of the Valve Spring in an Auto Engine during Plastic Hardening

N. Yu. Zemlyanushnova, A. A. Porokhin and N. A. Zemlyanushnov p. 535  abstract

Disk Concentrators in a System for Ultrasonic Surface Plastic Deformation of Screw Threads

V. V. Kolesnikov, S. M. Nebogov, V. I. Punin, S. A. Evsyukov and I. L. Fedotov p. 541  abstract

Using a Tool with Wear-Resistant Coatings in Transverse Cutting and Thread Cutting

V. P. Tabakov and D. I. Sagitov p. 545  abstract

Quantum-Mechanical Modeling of Chip Deformation and Failure

Yu. G. Kabaldin and A. M. Kuz’mishina p. 551  abstract

Surface Roughness in Final Turning: Development of an Adequate Empirical Model

V. B. Bokov p. 559  abstract

Neural-Network System for Extremal Control of the Cutting Precision

V. P. Legaev, L. K. Generalov and O. A. Galkovskii p. 565  abstract

Hybrid Treatment by a Laser Beam and Surface Plastic Deformation

V. F. Gubanov and M. A. Pesterev p. 571  abstract

Patent Activity of High-Tech Enterprises in the Republic of Udmurtia

A. N. Dombrachev, B. A. Yakimovich, A. I. Korshunov and S. I. Solomennikova p. 573  abstract

Design of Flexible Manufacturing Systems on the Basis of CAx Software and Virtual Modeling

K. S. Kul’ga, A. A. Kitaev, I. O. Sidorov and D. G. Kozhinov p. 577  abstract

Coordinating the Motion of a Robot and the Workpiece

M. K. Dadochkin p. 587  abstract

Cutting-System Dynamics

V. L. Zakovorotnyi and V. S. Bykador p. 591  abstract

Internal Grinding of Thermoprotective Rubber Coatings

A. M. Khanov, L. D. Sirotenko, L. P. Shingel’ and E. O. Trofimov p. 599  abstract

Influence of Misalignment of the Reamer and Spindle Axes on the Precision of the Machined Hole

G. S. Zheleznov and A. V. Shirokov p. 603  abstract

Monitoring the Yield of a Borehole Neutron Generator

A. A. Altukhov, T. B. Teplova, S. A. L’vov, E. V. Gladchenkov and S. A. Afanas’ev p. 607  abstract

---