Contents
Russian Engineering Research

Vol. 28, No. 6, 2008

Simultaneous English language translation of the journal is available from Allerton Press, Inc.
Distributed worldwide by Springer. Russian Engineering Research ISSN 1068-798X.

Bypass Gear Clutch for Nonfrictional High-Torque Speed Regulator

B. V. Pylaev and A. A. Shamin p. 517  abstract

Static Characteristics of Gas Bearings with a Rotary Bush

V. P. Legaev and Yu. S. Klimenkov p. 523  abstract

Influence of Forces on the Operation of a Mechanical Starting Clutch

E. N. Korneeva, B. G. Kobtsev, and Yu. S. Korneev p. 529  abstract

Influence of Gas-Dynamic Processes on Motor Efficiency and Durability

Yu. F. Gortyshov, V. M. Gureev, A. M. Druzhinin, and M. A. Zakonov p. 533  abstract

Parallel Solution of Creep and Heat-Conduction Problems by Means
of Nonlinear Generalized Models

Ya. M. Klebanov and V. G. Fokin p. 537  abstract

Dynamics of Oscillatory Systems with Controllable Shock Absorbers

G. S. Aver’yanov, R. N. Khamitov, and A. V. Zubarev p. 543  abstract

Adhesion of Liquid Flowing around a Solid Surface

I. V. Kholmogorov and V. Ts. Vanchikov p. 548  abstract

Thermooxidative Stability of TS_gip Transmission Oil

G. M. Sorokin, B. I. Koval’skii, Yu. N. Bezborodov, and N. N. Malysheva p. 551  abstract

Predicting the Frictional Wear Rate of Industrial Ceramics

Yu. N. Drozdov, V. A. Nadein, and T. M. Savinova p. 554  abstract

Nanostructuring of Metals in Fatigue Loading

Yu. G. Kabaldin p. 559  abstract

Characteristics of Gas–Abrasive Jets

M. G. Isupov and L. L. Lukin p. 566  abstract

Development of a New Theory of Cutting: 6. Determining the Basic Parameters of Cutting

A. L. Vorontsov, N. M. Sultan-Zade, and A. Yu. Albagachiev p. 571  abstract

Universal Kinematic Model of Cutting Processes

Yu. A. Novoselov p. 579  abstract

Determining the Quality of Precision Lathes on the Basis of Dynamic Characteristics

V. I. Zhiganov p. 584  abstract

Rotational Stability of Blank in Centerless Grinding with Longitudinal Supply

O. V. Zakharov p. 588  abstract

Regulated Pumping Drive of Metal-Cutting Shears

L. V. Nikonorov p. 592  abstract

Microstructure of Worn Surfaces of a Hard-Alloy Tool

S. Kh. Khadiullin p. 595  abstract

Deformation of a Helical Bit by Vibroacoustic Emission

E. S. Ognevenko p. 598  abstract

Determining the Strength of Abrasive Grains

O. I. Pushkarev and E. V. Slavina p. 600  abstract

Calculation of Operational Dimensions Using Techcard Software

S. A. Volkov and A. N. Ryabov p. 603  abstract

Removal of Material at Different Stages of Deep Plane Grinding

V. A. Nosenko, V. K. Zhukov, S. A. Zotova, and S. V. Nosenko p. 606  abstract

General Approach to the Optimization of Machining by Composite Tools

E. A. Kudryashov, A. M. Nikonov, and A. V. Stetsurin p. 611  abstract

Chip Texture in Metal Cutting

G. S. Zheleznov and S. G. Zheleznova p. 614  abstract

Cutting Forces in End Grinding by a Wheel

A. N. Khrokin and V. I. Svirshchev p. 617  abstract

Selection of the Conditions for Cutting Spatially Complex Surfaces
by Means of Radial Mills

B. D. Danilenko p. 619  abstract

Establishing the Basic Formulas in the Optimal-Specialization Model
for a Production System

A. V. Mukhin and Do Tien Lap p. 621  abstract

Pleiades Publishing home page | journal home page | top

If you have any problems with this server, contact webmaster.