Contents

Russian Engineering Research

---

Vol. 45, No. 5, 2025

---

Calculation of Main Parameters of Electrical Starting System of an Automotive Engine with a Direct Starter

E. V. Volkov p. 573  abstract

Improved Roll-Type Electrobaromembrane System

S. I. Lazarev, I. V. Khorokhorina, D. N. Konovalov, and O. V. Dolgova p. 580  abstract

Method of Control Point Charts in Statistical Product Control

N. I. Sidnyaev, and E. Battulga p. 584  abstract

Thermodynamic Principles for the Gas Filling of Chambers in Aerospace Components during Pneumatic Vacuum Tests

V. E. Scherba, V. V. Shalai, E. M. Khalatov, and A. R. Aliyev p. 591  abstract

Flat and Grid Electrodes in Crack Detection System for Gas Turbine Blades

I. K. Andrianov, M. K. Bally, and E. K. Chepurnova p. 596  abstract

Errors in Machining Axial Compressor Disks

G. A. Nesterenko, and I. S. Nesterenko p. 600  abstract

Accelerated Determination of the Endurance Limit Range for Structural Steels

K. V. Kuskov, A. A. Khyzov, and V. V. Voronin p. 604  abstract

Study of the Effect of Compaction and Thermal Compression Bonding on the Quality of Compact Materials Obtained by Recycling Titanium Alloy Scrap without Remelting

M. V. Zharov p. 610  abstract

Development of a Torque-Based Overload Protection System for a Hot Forging Press

A. V. Vanyagin, V. I. Erofeev, A. I. Ermolaev, S. N. Okhulkov, and A. S. Plekhov p. 616  abstract

External Wear of a Flush Pipe in a Drilling Rig

F. G. Amirov, and I. T. Shiraliyev p. 629  abstract

Surface Restoration of Metal Parts by Plasma Spraying of Powder

G. I. Trifonov, S. Yu. Zhachkin, and I. N. Kravchenko p. 635  abstract

Parallel Model of Turning for an Automated Control System

D. V. Simakov, and V. P. Legaev p. 641  abstract

Setup of a Production Quality Control System for Bearings

O. Yu. Zavozina, M. N. Zakharov, and Yu. V. Sinitsyna p. 645  abstract

Assessment of the Quality of Nickel Alloy Surface Layers after Grinding with Various Modes of Minimum Quantity Lubrication Supply

A. P. Mitrofanov, A. A. Isaeva, and K. A. Parsheva p. 651  abstract

Preproduction of Conical End Mills on a Five-Coordinate CNC Grinding Machine: Theoretical Analysis

V. A. Grechishnikov, V. A. Kuznetsov, A. A. Ershov, I. V. Minin, A. M. Yazev, and O. B. Nadykto p. 656  abstract

Pulsed Electromechanical Drives for General Industrial Use

K. Kh. Uzbekov, A. V. Priyadilov, E. S. Glibin, and A. A. Shevtsov p. 662  abstract

Sessile-Drop Laboratory System for Determining the Wettability of Refractories by Silicate Melts

S. V. Zaitsev, V. V. Strokova, V. A. Doroganov, and V. V. Sirota p. 667  abstract

Modeling the Rear Surface in the Design of Three-Flute Drills

P. M. Pivkin, V. A. Grechishnikov, A. A. Ershov, and I. G. Botryakova p. 671  abstract

Features of Information Support Systems for Quality Management Processes in Mechanical Engineering Enterprises

S. M. Bobrovsky, E. Yu. Malysheva, and R. A. Yafizova p. 675  abstract

Development of an Interactive Car Simulator

A. N. Baltabekova, P. Bouchner, K. K. Abishev, A. Zh. Kasenov, R. B. Mukanov, A. D. Suleimenov, and A. B. Bolatova p. 680  abstract

Intelligent Fuzzing Method for Aviation Information Systems as Part of the Secure Software Development Cycle

I. S. Antipov, S. S. Arustamyan, A. A. Ganichev, A. S. Markov, V. A. Pikov, A. A. Resinets, and A. I. Resinets p. 685  abstract

Breaking Down the Model of an Enterprise’s Production System into Individual Agents

Yu. G. Sledkov, L. L. Khoroshko, and P. M. Kuznetsov p. 691  abstract

Machine Learning in the Identification and Classification of Tree Species

K. D. Zhuk, F. V. Svoikin, V. F. Svoikin, L. G. Mishura, V. V. Kabakov, and S. N. Shkarubo p. 694  abstract

---