Contents
Russian Engineering Research


Vol. 32, No. 5–6, 2012

A simultaneous English language translation of this journal is available from Allerton Press, Inc.
Distributed worldwide by Springer. Russian Engineering Research ISSN 1068-798X.


Cyclic Degradation of Material in Vehicle Components

V. I. Mironov, O. A. Lukashuk, A. V. Yakushev, and G. G. Kozhushko p. 417  abstract

Improved Rotary Stretching and Softening Equipment for the Leather Industry

F. U. Nigmatova, D. I. Shin, and B. B. Akhmedov p. 423  abstract

Operation of a Centrifugal Pump and a Liquid Ejector with an Isobaric Mixing Chamber

V. Yu. Aleksandrov and K. K. Klimovskii p. 426  abstract

Control System for a Machine-Tool Drive with Compensation of Spindle Eccentricity

V. P. Legaev and L. K. Generalov p. 430  abstract

Operation of Two Induction Motors on a Dissipative Elastic Base

B. A. Gordeev and A. V. Leont’eva p. 433  abstract

Optimizing Cyclic Gearless Electric Drives with a Reduced-Speed Section

A. V. Sapsalev p. 438  abstract

High-Strength Antifrictional Elastoplastic Slip Bearings for Shipbuilding and the Power Industry

A. S. Oryshchenko, V. E. Bakhareva, A. V. Anisimov, and I. V. Lishevich p. 444  abstract

Thermoelastic Contact Instability with Mixed Lubrication in Frictional Components of Vehicles

I. A. Medelyaev p. 449  abstract

A New Method of Solving Complex Variational Problems: Examples of the Determination
of Broaching Parameters

A. L. Vorontsov p. 454  abstract

Crack Resistance of Tool Coatings in Continuous Cutting

V. P. Tabakov p. 464  abstract

Working Kinematic Front Angle in Turning a Sinusoidal Linear Surface

V. V. Vorona and I. A. Shchurov p. 469  abstract

Influence of Thermal Loads on the Stress–Strain State of Aluminum-Oxide Ceramic Cutting Plates

S. N. Grigor’ev, V. V. Kuzin, D. Burton, and A. D. Batako p. 473  abstract

Damping-System Design on the Basis of Electrochemical Modules

Yu. A. Pozhidaev and V. I. Kadoshnikov p. 478  abstract

Structural Precision of Metal-Cutting Machines

A. P. Kuznetsov and M. G. Kosov p. 482  abstract

Simulation of Hydraulic Machine-Tool Drives

Ya. A. Darsht and A. M. Filippov p. 491  abstract

Vibrational Tests of Lathes

V. V. Yurkevich p. 496  abstract

High-Speed Honing Tool for Deep Holes

V. A. Bakhvalov p. 498  abstract

Thermomagnetic Effect in the Chemicothermal Surface Hardening of Ceramic Cutting Plates

V. N. Puchkin, V. G. Solonenko, M. M. Aliev, T. V. Kononeko, and L. A. Solonenko p.501  abstract

Hybrid Machining in the Creation of Specified Residual Stress in the Surface Layer

E. S. Kiselev, E. N. Leksin, S. A. Romanov, and O. V. Blagovskii p. 504  abstract

Combined Finishing and Hardening in the Surface Plastic Deformation of a Plunger
by Diamond Smoothing

A. S. Kilov p. 508  abstract

High-Speed Grinding of ZhS6-K High-Temperature Nickel Alloy

A. Yu. Popov, D. S. Rechenko, K. V. Averkov, and V. A. Sergeev p. 511  abstract

Dimensional Analysis of Plate Heating

V. G. Miroshnichenko and V. N. Syrovatka p. 513  abstract

Calculation of Errors in Hole Machining by Ansys Software

S. V. Sergeev, D. V. Proshunin, and Yu. S. Sergeev p.515  abstract


Pleiades Publishing home page | journal home page | top

If you have any problems with this server, contact webmaster.