1 Transmission Lines with Sections of Different Productivity (q1 > q2), in the Case of Simultaneous Failures of the Sections and the Bunker
Contents
Russian Engineering Research
Vol. 30, No. 3, 2010
A simultaneous English language translation of this journal is available from Allerton Press, Inc.
Distributed worldwide by Springer. Russian Engineering Research ISSN 1068-798X.
Geometry of High-Temperature Oscillatory Gear Transmission
K. S. Ponosova and M. N. Karakulov p. 197 abstract
Loads on the Regulator of an Axial-Piston Pump
A. A. Chernyakov, A. P. Konov, and Ya. A. Darsht p. 201 abstract
Influence of the Gap in Clutches on the Dynamic Properties of Drives
I. A. Khalilov p. 206 abstract
Calculation of Shaft Reliability in Individual Belt Transmissions with Limited
Statistical Information Regarding the Basic Parameters
V. S. Utkin p. 213 abstract
Determining the Tribological Characteristics of Slipping Frictional Pairs
with Laser-Beam Hardening
V. P. Biryukov p. 216 abstract
Static Characteristics of Conical Multiple-Wedge Hydrodynamic Liquid-Friction Bearings
A. Yu. Korneev, L. A. Savin, and M. M. Yaroslavtsev p. 219 abstract
Operation of a Tight Joint under a Torque
A. S. Ivanov, M. M. Ermolaev, V. I. Grek, and E. N. Nikol’skaya p. 224 abstract
Automatic Discontinuous 2 1 Transmission Lines with Sections of Different
Productivity (q1 > q2), in the Case of Simultaneous Failures of the Sections and the Bunker
V. S. Gorchev p. 228 abstract
Improving Cutter Performance by the Application of Nanostructural Coatings
Yu. G. Kabaldin, S. V. Seryi, S. N. Murav’ev, A. A. Prosolovich, and E. V. Simagina p. 235 abstract
Machining of Gears with Circular Teeth by Means of an Eccentric Modifier
A. E. Volkov, V. I. Medvedev, and I. V. Zhuchkov p. 243 abstract
Selecting Abrasive Wheels for the Plane Grinding of Airplane Parts on the Basis
of Surface Roughness
Ya. I. Soler and D. Yu. Kazimirov p. 251 abstract
Surface Polishing of Machine Parts in Fine Turning of High-Temperature Alloys
by Superhard Cutters on Numerically Controlled Lathes
M. Kh. Uteshev and V. A. Belozerov p. 262 abstract
Energy-Saving Production of Anodic Nanocomposites
Yu. N. Boiko, D. V. Onishchenko, and A. A. Popovich p. 265 abstract
Dependence of the Yield Point of Steel on the Carbon, Chromium, and Nickel Content
E. I. Fradkin, G. A. Zhuravlev, and O. V. Tvarilidze p. 269 abstract
Development of a New Theory of Thermal Cutting Processes
3. Influence of Cutter’s Front Angle on the Cutting Temperature and Influence
of Preheating of the Blank on the Cutting Force
A. L. Vorontsov, N. M. Sultan-Zade, A. Yu. Albagachiev, and A. I. Savkin p. 274 abstract
Hydraulic Press with Two-Lever Control
Yu. M. Osokin and S. V. Kozlov p.276 abstract
New Steering Mechanism for Greater Vehicle Maneuverability
Z. A. Rustamov p. 278 abstract
Dynamic Simulation and Real-World Testing of Spindle Unit
A. M. Khanov, A. V. Shafranov, A. E. Kobityanskii, and A. V. Pepelyshev p. 281 abstract
Model of Hard-Alloy End Mills
K. N. Kolesov p. 285 abstract
Wear of High-Speed Steel Worm Mills in Cutting Cylindrical Gears
M. M. Kane and B. V. Ivanov p. 287 abstract
Improving the Wear Resistance of Ceramic Cutting Plates by Hot Nitriding
of the Surface Layer
V. G. Solonenko†, V. N. Puchkin, L. A. Solonenko, and T. V. Kononenko p. 291 abstract
More Efficient Superfinishing of Conical Surfaces
K. Yu. Luk’yanov p. 294 abstract
Vibrational Stability in Turning Thin-Walled Pipe by Multicutter Heads
G. T. Bykov, A. S. Yamnikov, O. A. Yamnikova, and N. B. Dorokhin p. 296 abstract
Correlation of the Components of Dimensional-Chain Elements
K. N. Abramov p. 300 abstract
Formalized Approaches in Technological Design
Yu. L. Chigirinskii p. 305 abstract
Processing Abrasive Waste
M. E. Butovskii p. 308 abstract
Deposition of Ion-Plasma Coatings on Tool Steels
L. L. Il’ichev and V. I. Rudakov† p.311 abstract
Pleiades Publishing home page | journal home page | top
If you have any problems with this server, contact webmaster.