Contents
Russian Engineering Research

Vol. 30, No. 2, 2010

A simultaneous English language translation of this journal is available from Allerton Press, Inc.
Distributed worldwide by Springer. Russian Engineering Research ISSN 1068-798X.

Cylinder of Internal-Combustion Engine with a Conical Working Surface

V. M. Gureev, A. M. Druzhinin, V. A. Stroganov, I. F. Gumerov, and M. A. Zakonov p. 105  abstract

Axial Force on the Screw of a Single-Flow High-Pressure Submersible Pump

V. M. Ryazantsev and V. V. Plyasov p. 109  abstract

Kinematic States of a Freely Moving Wedge Mechanism in Active Loading

A. A. Goncharov p. 112  abstract

Stability of the Initial Active-Surface Geometry and the Operational Smoothness
of an Involute Screw Transmission

V. A. Popov p. 119  abstract

Tractional Calculations for Vehicles with Adaptive Motors

I. K. Aleksandrov, E. V. Nesgovorov, and V. A. Rakov p. 122  abstract

Static Balancing of Rotating Bodies

O. O. Polushkin p. 125  abstract

Wear of Frictional Surfaces in High-Temperature Lead and Lead–Bismuth Coolants

A. V. Beznosov, T. A. Bokova, M. A. Antonenkov, K. A. Makhov, Yu. N. Drozdov,
V. N. Puchkov, and V. V. Makarov p. 128  abstract

Theory of Constrained Cutting: Calculating the Stress–Strain State in the Cutting Zone

S. I. Petrushin and A. V. Proskokov p. 133  abstract

Ultrasound Treatment of Heat-Resistant Materials with Compressed-Air Injection
in the Cutting Zone

A. A. Kozlov and M. N. Deryabin p. 138  abstract

Determining the Optimal Amplitudes and Directions of Ultrasound Vibrations
in Cutting Small-Module Gears

S. I. Agapov and I. G. Tkachenko p. 141  abstract

Surface-Layer Quality in Shot Treatment

M. A. Tamarkin, E. E. Tishchenko, and V. G. Lebedenko p. 144  abstract

Development of a New Theory of Thermal Cutting Processes
2. Temperature Distribution over the Chip Thickness

A. L. Vorontsov, N. M. Sultan-Zade, A. Yu. Albagachiev, and A. I. Savkin p. 149  abstract

Optimal Methodology for Cutting Studies

Yu. A. Novoselov p. 152  abstract

Diagnostics of the State of a Multicutter Hard-Alloy Tool on the Basis
of Thermoelectric Phenomena in the Cutting Zone

A. L. Plotnikov, E. G. Krylov, and E. M. Frolov p. 161  abstract

Calculation of Frictional Self-Oscillation

A. I. Levin and A. V. Ul’yanov p. 166  abstract

Profiling in Shaping Screw Surfaces

V. G. Shalamov and S. D. Smetanin p.170  abstract

Simulation of Cutting-Tool Stress States

M. Sh. Migranov and A. A. Stepanov p. 173  abstract

Uniform Microwave Heating of Semifinished Abrasive Tools with Thermoreactive
Organic Binders

S. M. Mikhailin and A. Sh. Khusainov p. 177  abstract

Basing Precision of Disk and Bush Blanks in Multipoint Machining

F. N. Abramov p. 181  abstract

Applicability of P6M5 Steel

A. M. Adaskin p. 186  abstract

Controlled Quenching of Tool Steels in Magnetizing Disperse Nanosystems

O. A. Avdeeva, O. A. Grishanina, and A. Ya. Simonovskii p. 190  abstract

Vibration- and Noise-Absorbing Polymer Composites Used in Manufacturing

D. E. Zharin, S. Yu. Yurasov, M. I. Gumerov, and L. N. Shafigullin p.194  abstract

Pleiades Publishing home page | journal home page | top

If you have any problems with this server, contact webmaster.