Contents
Russian Engineering Research

Vol. 30, No. 1, 2010

A simultaneous English language translation of this journal is available from Allerton Press, Inc.
Distributed worldwide by Springer. Russian Engineering Research ISSN 1068-798X.

Influence of Contact Stress on the Life of Connected Elements

G. G. Zaveryukha p. 1  abstract

Contact-Strength Estimates of the Reliability of Conical Gears
with Limited Statistical Information

V. S. Utkin p. 7  abstract

Simulating the Dynamic Reaction of Manipulator Supports

A. A. Dobrachev, L. T. Raevskaya, and A. V. Shvets p. 11  abstract

Contact Stress of Connected Axisymmetric Cylindrical Shells of Different Length
in Contact-Pressure Discontinuity Zones

A. M. Rubin p. 17  abstract

Edge Contact in Conical Transmissions with Round Gear Teeth

V. N. Rubtsov p. 20  abstract

Fatigue Strength of Materials in a Complex Stress State

A. E. Tsybul’ko and E. A. Romanenko p. 23  abstract

Frictional Properties of Aluminum Bronze Facings

V. V. Karzhavin, L. T. Plaksina, V. V. Ilyushin, and B. A. Potekhin p. 26  abstract

Automatic Discontinuous 2 1 Transmission Lines with Sections

of Different Productivity (q₁ < q₂)

V. S. Gorchev p. 31  abstract

Open Optimization in Two-Dimensional Lathe Control Systems

V. P. Legaev and L. K. Generalov p. 38  abstract

Pass-Through Lathe Cutter with Independent Cutting Systems

V. P. Cherkashin p. 41  abstract

Theory of Constrained Cutting: Chip Formation with a Developed

Plastic-Deformation Zone

S. I. Petrushin and A. V. Proskokov p. 45  abstract

Precision Basing of Blanks with Holes on Cylindrical and Truncated Pins

F. N. Abramov p. 51  abstract

Temperature in Contact Zone during Shot Hardening

I. G. Shin p. 61  abstract

Development of a New Theory of Thermal Cutting Processes 1. Basic Principles

A. L. Vorontsov, N. M. Sultan-Zade, A. Yu. Albagachiev, and A. I. Savkin p. 64  abstract

More Efficient Use of CAE Systems in Machine-Tool Design

A. N. Polyakov and S. V. Kamenev p. 67  abstract

Finite-Element Calculation of the Dynamic Characteristics of the Supporting

System of a Special Wheel-Boring Machine

Yu. V. Kirilin and N. V. Eremin p.72  abstract

Improving the Dynamic Precision of the Tool Position in a Machining Center

V. E. Lysov and Ya. I. Peshev p. 77  abstract

Efficiency of Numerically Controlled Metal-Cutting Machines

Ya. L. Liberman p. 81  abstract

Influence of the Composition of Three-Element Nitride Coatings on the State

and Wear of a Cutting Tool

V. P. Tabakov and A. V. Chikhranov p. 84  abstract

Influence of the Number of Segments and Their Dimensional Errors on the Primary

Imbalance Vector of a Grinding Wheel

V. G. Gusev and R. V. Zhigalov p. 90  abstract

Tool Management Systems

N. A. Chemborisov, R. M. Khisamutdinov, and D. R. Akhmetzyanov p. 94  abstract

Basing Precision of Disk and Bush Blanks in Multipoint Machining

F. N. Abramov p. 97  abstract

Machining of Housing Components in Attachments with Aerostatic Bearings

A. V. Lut’yanov p. 99  abstract

Precision of Duplicate-Milling Machine with a Spherical Head

Yu. A. Novoselov p.102  abstract

Pleiades Publishing home page | journal home page | top

If you have any problems with this server, contact webmaster.