Contents

Russian Engineering Research

---

Vol. 41, No. 12, 2021

---

Wear and Life of Saw Disks for Preliminary Cotton Processing

I. G. Shin, S. R. Nazarov, N. K. Iskandarova and M. R. Muminov p. 1115  abstract

Determining the Noncontact Deformation Produced by Orbital Indenter Action

S. A. Zaides and Pham Van Anh p. 1119  abstract

Synchronous Group Operation of Robots with Arbitrary Manipulator Kinematics

V. I. Chizhikov and E. V. Kurnasov p. 1124  abstract

Crack and Wear Resistance of Hard Coatings

V. A. Korotkov p. 1131  abstract

Modeling the Electrical Capacitance of Monitoring Sensors

A. N. Novozhilov, A. O. Yusupova and A. O. Potapenko p. 1135  abstract

Imbalance and Dynamics of a Disk Rotor

O. A. Polushkin, O. O. Polushkin and Ya. D. Koba p. 1140  abstract

Assessing the Fatigue Strength of Structural Materials by Assuming Equivalence of a Complex Stress State and Simple Extension. 1. Review of Experimental Data and Preliminary Analysis

P. N. Kozlov p. 1145  abstract

Reconfiguring the Metal-Hydride Linear Drive

S. N. Sayapin p. 1149  abstract

Standardizing the Permissible Mass Error in Monitoring Connecting Rods and Pistons

M. N. Erokhin, O. A. Leonov, N. Zh. Shkaruba, P. V. Golinitskii and U. Yu. Antonova p. 1156  abstract

Losses in the Input Channel of a Two-Rotor Vacuum Pump

A. A. Isaev, A. A. Raikov, A. V. Burmistrov and S. I. Salikeev p. 1161  abstract

Characteristics of a Vortex Diode of Increased Diodicity

S. Yu. Kaigorodov and I. V. Tsvetkov p. 1165  abstract

Influence of the Hydrodynamics of Electrolyte Flow on the Surface Quality in Electrochemical Machining

D. A. Rastorguev, K. O. Semenov, R. R. Dema, M. V. Kharchenko and O. R. Latypov p. 1169  abstract

Producing Electrodes for Innovative Power Sources by Thin-Film Technology

V. V. Sleptsov, D. Yu. Kukushkin, S. N. Kulikov, A. O. Diteleva and R. A. Tsyrkov p. 1175  abstract

Automated Calculation of Grinding by a Cubic Carbon Nitride Wheel and Solid Lubricant, with Wheel Wear

V. A. Panaioti, S. S. Zhluktov, E. V. Kopytova and A. M. Petukhov p. 1179  abstract

Cutter Wear in a One-Sided Drill

L. A. Kondratenko, L. I. Mironova, V. M. Terekhov and M. Yu. Khizhov p. 1183  abstract

Coordinating the Operation of a Robot’s Manipulator and Vision System

N. V. Kim, M. I. Mokrova and V. V. Polyanskii p. 1189  abstract

Management on the Basis of Key Performance Indicators at Manufacturing Enterprises

V. V. Lastochkina p. 1193  abstract

Lean Production at High-Tech Enterprises

S. V. Novikov p. 1196  abstract

Accounting and Commercialization Practices for Intellectual Property in Russia

P. D. Milovanov p. 1199  abstract

Assessing the Use of Information Technology in Russia

L. M. Davletshina and V. V. Lastochkina p. 1203  abstract

Improving Management Efficiency at Aerospace Enterprises

E. E. Galkina, A. E. Sorokin and T. V. Golovanova p. 1206  abstract

Architecture of Software for Simulating Drone Operation

V. N. Evdokimenkov, R. V. Kim and S. S. Popov p. 1209  abstract

Integrated Logistical Support Based on Probabilistic Guaranteed Assessment of the Aircraft Condition

V. N. Evdokimenkov, R. V. Kim and I. S. Mikhailin p. 1213  abstract

Characteristics of the Medical Support System for Interplanetary Flight

I. N. Belozerova and N. S. Kudryavtseva p. 1217  abstract

Exergy Analysis of Heat Management Systems in Spacecraft with Heat Stores

A. E. Belyavskii p. 1221  abstract

Exergetic Analysis of Spacecraft Thermal Control Systems with a Heat Store

A. E. Sorokin p. 1224  abstract

Beacon Network Initialization in Lunar Navigation System Development

E. V. Akimov, S. Yu. Bakharev, D. A. Kozorez and D. M. Kruzhkov p. 1227  abstract

Local Plastic Deformation in Shaping Thin-Walled Aircraft-Engine Components

A. V. Martynyuk, V. V. Kuritsyna and M. V. Siluyanova p. 1230  abstract

Reorganization of Machine-Tool Repair in Manufacturing

Yu. G. Sledkov, L. L. Khoroshko and P. M. Kuznetsov p. 1233  abstract

Noise Characteristics of Chain Drives with Involute Sprockets

G. V. Kurapov and S. B. Berezhnoi p. 1236  abstract

Design of Roller Beams Using SolidWorks Software

S. Yu. Kalyakulin, A. P. Martyshkin, E. V. Mitin and S. P. Sul’din p. 1239  abstract

Design of Spatial Deployable Modular Constructions Based on Planar Kinematic Chains

A. S. Fomin and D. V. Petelin p. 1242  abstract

Indices for Digital Quality Management at Auto Plants

D. I. Blagoveshchenskii, V. N. Kozlovskii and S. A. Vasin p. 1247  abstract

Key Aspects of the Digitization of Quality Control in Auto Assembly

D. I. Blagoveshchenskii, V. N. Kozlovskii and S. A. Vasin p. 1251  abstract

Digital Tools for Statistical Quality Management in Automobile Production

D. I. Blagoveshchenskii, V. N. Kozlovskii and S. A. Vasin p. 1255  abstract

Effectiveness of Neural Networks in Predicting Machine-Tool Temperatures

V. V. Pozevalkin and A. N. Polyakov p. 1260  abstract

Lean Production Principles in Production Management

N. V. Prosvirina, A. I. Tikhonov and H. I. Okagbue p. 1263  abstract

Influence of Supply Chains on the Sustainable Development of Manufacturing Companies

R. S. Golov, L. A. Kostygova, D. A. Prokof’ev, K. V. Anisimov and A. M. Andrianov p. 1269  abstract

Supply Chain Management for Sustainable Development of the Manufacturing Industry

R. S. Golov, L. A. Kostygova, D. A. Prokof’ev, K. V. Anisimov and A. M. Andrianov p. 1272  abstract

Energy Management System for an Industrial Enterprise

R. S. Golov, V. G. Smirnov, V. Yu. Teplyshev, D. A. Prokof’ev, A. G. Palamarchuk, K. V. Anisimov and A. M. Andrianov p. 1275  abstract

---