Contents

Russian Engineering Research

Vol. 43, No. 10, 2023

Roller Bearing with Gear Engagement

E. N. Pashkov and D. D. Dubrovskiy p. 1167  abstract

Thermal Calculation of Armatures in Locomotive Tractional Electric Motors

A. M. Lyashchenko, D. V. Glazunov and D. V. Shvalov p. 1171  abstract

Using Plastic Pinions with a Steel Wrapper in Planetary Cycloid Gears

M. N. Zakharov, M. M. Ermolaev and N. N. Kuralina p. 1173  abstract

Optimal Hardness Ratio of Wheel Steel and Rail Steel for Minimum Wear

A. T. Kanaev, A. E. Moldakhmetova and A. V. Bogomolov p. 1178  abstract

Stability of Nonlinear Electromechanical Systems with a Magnetic Gearbox

A. V. Sapsalev, S. A. Kharitonov and A. A. Achitaev p. 1183  abstract

Determining the Residual Stress in Thin Coatings from Their Flexure after Indentation

N. A. Voronin p. 1189  abstract

New Coaxial Magnetic Multiplier for Size-Limited Hydraulic Channels

K. A. Bashmur and Yu. V. Abramov p. 1195  abstract

Effect of Thermoelectric Properties on the Frictional Behavior of High-Speed Steels

E. V. Fominov, K. G. Shuchev, M. M. Aliev, A. A. Marchenko and T. V. Lavrenova p. 1199  abstract

Minimizing the Machining Temperature in Reversible Surface Plastic Deformation

S. A. Zaides and Nguyen Huu Hai p. 1204  abstract

Three-Dimensional Phase Flows during Mass Transfer of Liquids in Machines with Self-Exciting Two-Rotor Vibrational Drives

Yu. S. Sergeev, S. V. Sergeev and A. V. Zenin p. 1210  abstract

Stamping of Nonuniform Channels. 8. Strain State and Hardening of the Workpiece in Constrained Extrusion. 8.1. Plastic Zone under the Thick Wall

A. L. Vorontsov p. 1218  abstract

Acoustic Emission Diagnostics of Damaged MS-21 Airplane Wingbox during Endurance Tests

Yu. G. Matvienko, I. E. Vasil’ev, D. V. Chernov, S. V. Dubinsky, R. V. Voronkov and A. G. Yashutin p. 1223  abstract

Influence of Tool Microgeometry on Technological Inheritance in Hybrid Hole Burnishing

A. V. Shchedrin, L. Kh. Minyazeva, A. A. Bekaev, N. Yu. Chikhacheva and T. A. Burlakova p. 1234  abstract

Influence of Milling Trajectory on Tool Wear

N. G. Shishkov and Zh. E. Chulikova p. 1240  abstract

Production and Repair of Agricultural Equipment: Analysis by the 5M Principle

M. N. Erokhin, O. A. Leonov, N. Zh. Shkaruba, Yu. G. Vergazova and D. M. Skorokhodov p. 1242  abstract

Improving Hole Geometry in Honing

K. R. Muratov, T. R. Ablyaz, A. A. D’yakonov, E. A. Gashev and S. Singh Sidhu p. 1246  abstract

Correction of the Technological Inheritance in Belt Grinding of Gas-Turbine Engine Blades

D. I. Volkov, A. A. Koryazhkin, A. V. Kurochkin, A. N. Sutyagin and I. V. Il’in p. 1249  abstract

Control of Tool–Workpiece Contact in Belt Grinding

D. I. Volkov, A. A. Koryazhkin, A. V. Kurochkin, A. N. Sutyagin and N. N. Sokolov p. 1254  abstract

Productivity Control Software for Belt Grinding of Blades Used in Gas-Turbine Engines

D. I. Volkov, A. A. Koryazhkin, A. V. Kurochkin and A. N. Sutyagin p. 1259  abstract

Influence of Wire-Cut Electrical Discharge Machining on the Three-Dimensional Structure of Polymer Composites

T. R. Ablyaz, E. V. Plotnikov, E. S. Shlykov, I. V. Osinnikov, I. A. Panteleev, V. A. Mubassarova and S. Singh Sidhu p. 1263  abstract

Optimal Electric Discharge Machining of Heat-Resistant Alloys

T. R. Ablyaz, A. Yu. Gorokhov, A. A. Kamenskikh, E. S. Shlykov and K. R. Muratov p. 1266  abstract

Tools for Project Analysis

E. V. Surkova and V. V. Kabakov p. 1269  abstract

Applicability of Piezoceramic Components in the Automotive Industry

E. V. Stepanov, A. S. Vashurin, A. V. Tumasov and E. I. Toropov p. 1273  abstract

Trusted CNC System Based on the AxiOMA Control Platform

G. M. Martinov, R. L. Pushkov, L. I. Martinova and S. V. Sokolov p. 1279  abstract

Enterprise Development Planning and AI-Based Technological Forecasting

R. A. Nezhmetdinov, M. A. Charuiskaya and I. A. Kovalev p. 1284  abstract

Industrial Innovation in Russia Today

V. A. Zolotova p. 1289  abstract

Introducing Integrated Management Systems in the Aerospace Industry

E. E. Galkina and A. E. Sorokin p. 1294  abstract

Financial Models for the Commercialization of Research and Development Results

M. N. Kaloshina and T. Yu. Nikolenko p. 1297  abstract

Tools for Assessing the Innovative Development Potential in Russia’s Regions

V. N. Kozlovskii and A. S. Klentak p. 1301  abstract

Neural Network Derivation of Optimal Digital Twins for Innovative Alloys and Composites

A. A. Burdina, I. A. Bobkov, S. S. Burdin and A. A. Nekhrest-Bobkova p. 1306  abstract

Effectiveness of Testing Digital Twins of Aircraft Components

A. A. Burdina, N. V. Moskvicheva and D. G. Nabieva p. 1310  abstract

Fuzzy Logic in Risk Management at High-Technology Enterprises

A. A. Burdina, N. V. Moskvicheva and N. O. Melik-Aslanova p. 1314  abstract

Crisis Diagnostics in Corporate Management

A. N. Genova p. 1318  abstract

Quality Assessment of New Cars by Expert Analysis

V. N. Kozlovskii, R. R. Gafarov, A. S. Klentak and D. V. Aidarov p. 1322  abstract

Questionnaires in Assessing Consumer Satisfaction with Vehicle Quality

V. N. Kozlovskii, R. R. Gafarov, A. S. Klentak and A. V. Kerov p. 1326  abstract

Engineering Tools for Assessing Consumer Satisfaction with Vehicle Quality

V. N. Kozlovskii, R. R. Gafarov, A. S. Klentak and D. S. Gordienko p. 1329  abstract

Basic Components of an Engineering System for Assessing Consumer Satisfaction with Vehicle Quality

V. N. Kozlovskii, R. R. Gafarov and A. S. Klentak p. 1332  abstract

Assessing Consumer Perceptions of Product Quality in the Auto Industry

D. S. Gordienko, D. V. Aidarov, V. N. Kozlovskii and A. S. Klentak p. 1337  abstract