Contents

Russian Aeronautics

Vol. 67, No. 1, 2024

STRUCTURAL MECHANICS AND STRENGTH OF FLIGHT VEHICLES

Nonlinear Deformation and Stability of Anisogrid Circular Cylindrical Shells under Pure Bending and Internal Pressure

L. P. Zheleznov p. 1  abstract

Dynamic Behavior of an Unevenly Heated Thin-Walled Parabolic Aircraft Shell Taking Into Account the Presence of Additional Mass under the Influence of a Shock Wave

I. K. Turkin p. 16  abstract

FLIGHT DYNAMICS AND CONTROL OF FLIGHT VEHICLES

The Influence of the Angular Dimension of Rectangular Cutouts on the Stress and Strain State of Sandwich Cylindrical Compartments

V. N. Bakulin p. 22  abstract

Suppression of Pilot-Induced Oscillations of Various Categories Using Augmentation Means

A. V. Efremov, E. V. Efremov, and A. I. Shcherbakov p. 33  abstract

Aircraft Flight Safety Assessment Based on Aviation Incident Risk Analysis

V. A. Shevtsov, A. V. Timoshenko, and S. N. Razin’kov p. 43  abstract

AERO- AND GAS-DYNAMICS OF FLIGHT VEHICLES AND THEIR ENGINES

Influence of Dispersed Particles on Structure of a Vortex Ring and Its Propagation

K. N. Volkov, V. N. Emel’yanov, and I. E. Kapranov p. 50  abstract

Exact Solutions to the Navier–Stokes Equations for Describing the Flow of Multicomponent Fluids with Internal Heat Generation

E. Yu. Prosviryakov, O. A. Ledyankina, and L. S. Goruleva p. 60  abstract

Optimization of the Aerodynamic Configuration of the Isolated Wing for the Second-Generation Supersonic Passenger Aircraft

M. V. Shirokov, D. Yu. Strelets, and I. G. Bashkirov p. 70  abstract

AIRCRAFT AND ROCKET ENGINE DESIGN AND DEVELOPMENT

Research and Development of Recommendations for Building a Computational Grid for Numerical Simulation of Typical Internal and External Flows in Relation to Aeronautical Engineering Problems

S. K. Osipov, P. A. Bryzgunov, V. P. Sokolov, I. V. Shevchenko, and I. A. Milyukov p. 80  abstract

AIRCRAFT AND ROCKET ENGINE THEORY

On the Effect of Internal Aerodynamics and Fuel Combustion Rate on the Thrust of a Valveless Pulsejet Engine

K. V. Migalin, D. A. Charntsev, and K. A. Sidenko p. 88  abstract

Improving the Accuracy of Performance Calculation for Multistage Axial Turbines of Aircraft Engines Using Three-Dimensional Numerical Modeling

G. M. Popov, V. M. Zubanov, E. S. Goryachkin, and A. I. Shcherban p. 96  abstract

Numerical Simulation of the Lubrication System of Aircraft Piston Engines

I. A. Popov, M. V. Gureev, V. M. Gureev, Yu. V. Zhukova, and A. D. Chornyi p. 103  abstract

Model of Convective-Film Cooling of Plate with Flow Nonstationarity and Gas Compressibility

A. L. Tukmakov, A. A. Akhunov, N. A. Tukmakova, and V. V. Khar’kov p. 110  abstract

AIRCRAFT INSTRUMENTS AND INSTRUMENTATION COMPUTER COMPLEXES

Experimental Testing of Using the Artificial Neural Networks in Diagnostic Systems for Assessing and Predicting the Technical Condition of Rotorcraft Units

A. B. Bel’skii, O. A. Esipovich, and B. B. Safoklov p. 119  abstract

An Optimal Control Synthesis for a Gyro-Stabilized Platform Stabilization Loop

K. O. Lukin, and S. V. Krivosheev p. 127  abstract

AIRCRAFT PRODUCTION TECHNOLOGY

Fretting-Wear of Chemical NiP Coatings Deposited on Parts for Aircraft Engines and Power Plants Obtained by Selective Laser Melting from AlSi10Mg Alloy

I. R. Aslanyan, M. S. Eremkina, and A. V. Ionov p. 138  abstract

Mechanical Characteristics of a Product Manufactured by the FDM Printing

L. I. Garipova, A. S. Batrakov, and F. F. Khabibullin p. 145  abstract

Study of the Influence of Erosive Combustion of Solid Fuel on the Intra-Ballistic Parameters of a Jet Penetrator

E. V. Gusev, V. A. Zagovorchev, P. F. Pronina, V. V. Rodchenko, and E. R. Sadretdinova p. 151  abstract

Determination of the Area of Workpiece Destruction during the Deep Drawing into a Conical Die

E. G. Dem’yanenko, I. P. Popov, and D. A. Nikonov p. 161  abstract

AIRCRAFT AND ROCKET ENGINE THEORY

Study of the Load-Bearing Capacity of Composite Structures with Various Reinforcement Patterns in the Zone of the Open Hole

D. Yu. Konstantinov, V. I. Khaliulin, V. V. Batrakov, and R. Yu. Petrushenko p. 170  abstract

AIRCRAFT PRODUCTION TECHNOLOGY

Thermoforming of Products from Consolidated Sheet Blanks Based on the Polypropylene Reinforced by the Fiberglass

R. I. Solov’ev, D. A. Bal’kaev, and L. M. Amirova p. 183  abstract

RADIO ENGINEERING AND COMMUNICATION

Experimental Study of Electromagnetic Resistance of Technical Systems Exposed to Electromagnetic Effects from Several Sources

R. R. Gainutdinov, and S. F. Chermoshentsev p. 192  abstract

STRUCTURAL MECHANICS AND STRENGTH OF FLIGHT VEHICLES

Computational Experiment in the Problem of the Flutter of a Cylindrical Shell

S. D. Algazin p. 198  abstract

Numerical Study of Influence of Inclined Crack Geometrical Characteristics in a Turbine Blade of the R-2617a Profile on a Failure Pressure in the Damage Detection System

I. K. Andrianov, M. S. Grinkrug, and M. Kara Bally p. 203  abstract

AIRCRAFT INSTRUMENTS AND INSTRUMENTATION COMPUTER COMPLEXES

Methodology for Monitoring the Performance of Measuring Equipment for Testing the Propulsion Systems

A. R. Vorob’ev, and V. B. Fedorov p. 209  abstract

AIRCRAFT PRODUCTION TECHNOLOGY

Elements of the Optimizing Algorithm for the Vacuum Infusion Technological Process in the Manufacture of Large-Sized Products Made of Polymer Composite Materials

A. P. Koval’, and I. O. Bobarika p. 215  abstract