Contents

Polymer Science, Series D

Vol. 18, No. 3, 2025

Assessment of the Effect of the Nature of a Flame-Retarding Additive on the Properties of Films Based on PVA

N. A. Keibal, V. F. Kablov, V. G. Kochetkov, D. A. Kryukova, D. A. Urzhumov, and A. I. Slukhanchuk p. 453  abstract

The Influence of Appret Concentration and Its Application Technology on the Property Complex of Epoxy-Binder-Based Basalt Plastics

A. S. Borodulin p. 460  abstract

The Relationship of Surface Energy Parameters and Adhesion Characteristics of Modified Ethylene Copolymer–Metal Compounds

I. A. Starostina, K. B. Vernigorov, N. A. Kuzina, R. A. Perelygina, Yu. M. Kazakov, and O. V. Stoyanov p. 464  abstract

Evaluation of Fatigue Behavior of Bitumen Binders by the Linear Amplitude Sweep Test: Failure Criteria and Fatigue Parameters

V. N. Gorbatova, I. V. Gordeeva, T. V. Dudareva, I. A. Krasotkina, and A. A. Berlin p. 469  abstract

Photopolymerization of Cyanoacrylates and Adhesives Based on Them (A Review)

D. A. Aronovich p. 480  abstract

The Influence of Two-Step Processing of Wood Filler on the Properties of Polyethylene-Based Wood–Polymer Composites

K. G. Anikeeva, and R. R. Safin p. 493  abstract

The Influence of Temperature Factors on Adhesion Strength of Fiber–Matrix in Carbon-Fiber-Reinforced Polyimide Composite

A. I. Gulyaev, S. V. Sbitneva, M. I. Valueva, and I. V. Zelenina p. 497  abstract

The Influence of Modified Fillers on Flame-Retardant Properties of Polyvinyl Chloride Plastisol

V. F. Kablov, N. A. Keibal, T. V. Krekaleva, A. G. Stepanova, V. G. Kochetkov, V. A. Drozdev, and V. O. Kharlamov p. 503  abstract

Study of Dielectric Constant, Shrinkage, and Residual Stresses during Curing of Epoxy Oligomers

G. I. Ezdakov, D. A. Trofimov, A. M. Khort, and I. D. Simonov-Emel’yanov p. 510  abstract

Synthesis of Aqueous Dispersions of Functionalized Styrene–Acrylic Copolymers and Preparation of Hybrid Polyurethane–Acrylic Coatings Based on Them

N. I. Hloba, A. Yu. Balash, A. L. Egorova, and E. T. Krut’ko p. 516  abstract

Analysis and Improvement of Adhesive Compositions to Glue Wood Veneer

E. G. Sokolova p. 525  abstract

A Study of the Physical and Mechanical Properties of Modified Fire-Retardant Wood Materials

N. G. Kolesov, G. S. Varankina, A. B. Shishlyannikova, and D. S. Rusakov p. 530  abstract

Effect of Modifying Additives on Adhesive Characteristics of Composites Based on Nitrile–Butadiene Rubber–Tiokol Mixtures

K. N. Slobodkina, K. B. Vernigorov, Kh. S. Abzal’dinov, Yu. M. Kazakov, and O. V. Stoyanov p. 535  abstract

The Effect of the Characteristics of a Polyol Component of PU Binders on the Properties of Composites

Yu. Yu. Yakovlev, N. P. Bezrukov, Yu. I. Yavorskii, and A. A. Akulinicheva p. 540  abstract

Synthesis and Study of the Mechanism of Flame Retardation of Polymer Materials

F. B. Abdukadirov, A. A. Berlin, B. Kh. Mirzakhmedov, F. R. Eshbaeva, and B. A. Mukhamedgaliev p. 547  abstract

A Method for Predicting the Durability of Anticorrosion Paint Coatings Based on Analysis of Changes in the Capacitance–Frequency Coefficient under the Influence of Aggressive Environments

A. N. Potapchik, and A. L. Egorova p. 551  abstract

A Theoretical Justification of the Applicability of the Method of Deformation-Free Fixing of Workpieces on Cyanocrylate Adhesives during Cutting

A. S. Kononenko, I. Yu. Ignatkin, and R. R. Khabbatullin p. 558  abstract

Modification of Epoxy Resin ED-20 with Copper and Ammonium Phosphates

A. A. Lyubibogov, D. A. Khamzina, S. V. Borisov, I. A. Stenina, Yu. M. Evtushenko, M. A. Vaniev, and I. A. Novakov p. 567  abstract

Compression of Hydrogen Atom. Gravity. Temperature

R. A. Turusov p. 574  abstract

Use of Hemp (Cannabis sativa) Biomass Components and Activated Carbons Based on Them to Remove Pollutants from Aqueous Media: 1. Metal Ions

I. G. Shaikhiev, E. N. Khabibrakhmanova, K. I. Shaikhieva, and T. R. Deberdeev p. 579  abstract

Novel Polymer Flame Retardants for Decreasing the Flammability of Cellulose Materials

F. B. Abdukadirov, A. A. Berlin, A. B. Sivenkov, A. A. Abdurakhimov, and B. A. Mukhamedgaliev p. 586  abstract

Potential for the Use of Silicone Molds in the Manufacture of Parts for Ground-Based Transport and Technological Machines and Complexes Using Shell Casting Technology

A. O. Dvoryankin, and N. I. Baurova p. 590  abstract

Investigation of the Structure and Properties of a Thermal Protective Polymer Coating

O. I. Sidorov, V. A. Pil’chenko, T. V. Bochkova, D. V. Zhesterev, D. V. Pleshakov, M. I. Buzin, V. P. Shantarovich, and I. B. Kevlina p. 594  abstract

The Influence of the Structural State of Hot-Stamped Powder Steels on Their Behavior during Heat Treatment

V. A. Skryabin p. 604  abstract

Use of Cereal Crop Processing Waste to Remove Hydrocarbon Spills from the Water Surface: 4. Fruit Shells of Barley, Oat, and Buckwheat Grains (A Literature Review)

I. G. Shaikhiev, K. I. Shaikhieva, S. V. Sverguzova, and T. R. Deberdeev p. 609  abstract

Prospects for the Use of Polymer Knitted Fabrics as Interlining Materials in Special Sewing Products with Monitoring Functions

V. V. Getmantseva, M. A. Guseva, O. D. Shashkova, and M. I. Khoteeva p. 615  abstract

A Study of the Influence of Postprocessing Methods on the Resistance of 3D-Printed Parts to Aggressive Environments

I. S. Nefelov, and N. I. Baurova p. 622  abstract

A Study of the Influence of 3D Printing Modes on the Tightness of Mechanical Engineering Products Manufactured Using Additive Technologies

I. S. Nefelov, and N. I. Baurova p. 628  abstract

Influence of Nonionic Surfactants on the Properties of Polyurethane Urea Films

A. V. Savchuk, and V. Yu. Senichev p. 634  abstract

Development of Technology for Stabilizing Mammoth Tusks of Grades III—IV

G. V. Botvin, A. A. Chirikov, V. V. Petrov, T. A. Isakova, V. V. Pavlova, T. M. Solov’ev, D. R. Khabarov, and E. S. Petukhova p. 641  abstract

Effects of Soil Environment on Multicomponent Blends Based on Polyethylene and Its Secondary Analog

Yu. V. Tertyshnaya, and M. V. Podzorova p. 646  abstract

Investigation of Properties of Polymer Composites Based on Plasticized Cellulose Ether (Ester) Blends

K. A. Usova, A. E. Shkuro, and V. V. Glukhikh p. 652  abstract

Analysis of the Chemical Composition of Titanium-Based Alloys for the Production of Dental Implants

V. A. Ivanova, V. A. Put’, S. A. Put’, and G. V. Smirnov p. 658  abstract

A Study of the Strength Properties and Radiation Resistance of Carbon–Carbon Composite Material for Medicine

V. D. Oniskiv, V. Yu. Stolbov, and A. V. Sotin p. 662  abstract

Processing of Postextraction Pine Needle Residue Using Fast Pyrolysis

G. M. Bikbulatova, V. N. Bashkirov, A. R. Valeeva, A. N. Grachev, R. M. Khaziakhmedova, and M. P. Chernov p. 667  abstract