Vol. 16, No. 1, 2023
A Study of the Effect of Negative Temperatures on the Stress–Strain State of Glue-Welded Joints
p. 1 abstract
Preservation of Properties of Functional Materials of Aviation Equipment under a Tropical Humid Climate
p. 4 abstract
Properties of Conductive Adhesive with Carbonyl Nickel as Filler
p. 9 abstract
A Review of Modern Adhesive Materials Operating in a Wide Temperature Range. Epoxy Adhesives
p. 14 abstract
An Investigation of the Effect of Gas Generators on the Physical and Mechanical Characteristics of Compositions Based on Polyacrylamide
p. 34 abstract
Waterproof Plywood Based on Aminoformaldehyde Resin of AFK-8 Brand
p. 40 abstract
Synthesis and Properties of Phenol–Formaldehyde Resins from Thermal-Processing Products of Wood
p. 43 abstract
Application of Adhesives for Gluing Various Glasses (Survey). Part 1. Adhesives for Aircraft Glazing and Gluing Organic Glasses
p. 51 abstract
Application of Adhesives for Gluing Various Glasses (Survey). Part 2. Gluing Silicate Glasses
p. 56 abstract
A Heat-Resistant Film Adhesive on the Basis of Cyane Ethers
p. 63 abstract
Amphiphilic Properties of Methacrylic Macromonomers with Oligo(ethylene glycol) and Oligo(propylene glycol) Blocks
p. 69 abstract
Flame-Retardant Reinforced “Soft”-Cured Composites Based on Polyphosphates
p. 76 abstract
Rheological Properties of Composite Materials for Manufacturing Sprayers of Agricultural Sprinklers
p. 83 abstract
The Influence of Technological Modes on the Quality of Coatings Made of Powder Polymer-Composite Materials
p. 89 abstract
Sticking Control of Prepregs Based on ED-20 Resin
p. 94 abstract
Adhesion Properties of Metal-Filled Functionalized Polypropylene-Based Nanocomposites
p. 98 abstract
Delamination of Composites and the Scale Effect of Glued Joint Strength
p. 104 abstract
Casting Compositions Based on Phosphorus-Containing Polyol, Melamine Polyphosphate, and Copper Orthohydrophosphate for the Design of Low-Combustible Foamed Polymurethanes
p. 111 abstract
The Formation of Microcracks during Climatic Aging of Polymer-Composite Materials
p. 116 abstract
Influence of Carbon Nanotubes on the Radiotechnical Characteristics of Radiation-Absorbing Materials
p. 124 abstract
The Influence of Diurnal and Seasonal Variations of Relative Humidity and Temperature on Coal–Plastic Moisture Saturation in Open Climatic Conditions
p. 131 abstract
High-Temperature Thermodestruction Analysis of a Polyphenylene-Sulfide-Based Composite by Thermogravimetry
p. 137 abstract
Hierarchical Structure Arrangement Levels, Parameters, and a Set of Physicomechanical Characteristics for Structural Fiberglass Fabrics
p. 142 abstract
Modern Prepregs Based on Polymer Organic Fibers for the Manufacture of Aerostructures
p. 148 abstract
Mechanical Characteristics of Compositions Based on Polyethylene and Polylactide under the Action of Aggressive Environmental Factors
p. 154 abstract
Polymer Composites Based on Polylactide and Reduced Graphene Oxide
p. 161 abstract
Composites Based on Latexes and Tetrafluoroethyene Telomers for Coatings of Wood Materials
p. 168 abstract
Simulation of Optimal 3D Printing Parameters
p. 173 abstract
Obtaining Oligoether Polyols from Secondary Polyethylene Terephthalate
p. 178 abstract
The Structure and Properties of Materials Obtained by Impregnation
p. 184 abstract
Review of Methods for Creating Orderly Reinforced Composites Based on Thermoplastic Polymers
p. 188 abstract
Physical and Mechanical Properties of Filled Nanocomposites Based on Thermoplastic Copolymers of Ethylene with α-Olefins
p. 193 abstract
A Comparative Assessment of the Influence of Modification with Thermoplastic Powders on the Residual Compressive Strength of the Carbon Fiber Reinforced Polymers
p. 199 abstract
Polymeric Material Stability in a Hydrogen Fluoride Environment
p. 207 abstract
Influence of DSC Thermogram Processing Methods on the Results of Calculation of Kinetic Parameters of the Curing Reaction of a Thermoreactive Binder
p. 215 abstract