Vol. 9, No. 6, 2018

Inorganic Materials: Applied Research

Vol. 9, No. 6, 2018

A simultaneous English language translation of this journal is available from Pleiades Publishing, Ltd.
Distributed worldwide by Springer. Inorganic Materials: Applied Research ISSN 2075-1133.

Metal Sciences. Metallurgy

Structure Changes of High-Strength Economically Alloyed Steel 09KhGN2MD (09CrMnNi₂MoCu) In Tempering

M. V. Golubeva, O. V. Sych, E. I. Khlusova, G. D. Motovilina, E. V. Sviatysheva, S. V. Rogozhkin and A. A. Lukyanchuk p. 997 abstract

Carburization of Heat-Exchanger Pipes of 09Kh18N9 Grade Steel in Contact with Sodium Coolant

A. S. Kudryavtsev and K. A. Okhapkin p. 1006 abstract

Refractory Monocarbides and Diborides of Transition Metals: Promising Components of High-Temperature Composite Materials

G. S. Burkhanov and V. A. Dementiev p. 1012 abstract

Concentration Redistribution of Alloying Elements in Pseudo-Alpha-Titanium Alloy under Elastoplastic Deformation

L. A. Ivanova, G. V. Benemanskaya and V. V. Travin p. 1020 abstract

Research on Submicron-Grained Structure Formation in Titanium Alloys upon Reversible Hydrogenation and Plastic Deformation

P. V. Panin, S. S. Manokhin and D. A. Dzunovich p. 1029 abstract

Structural Features of Niobium Carbide Disperse Particles in the Structure of Heat-Resistant Alloys Based on Fe–25Cr–35Ni System

S. Yu. Kondratiev, E. V. Sviatysheva and S. N. Petrov p. 1035 abstract

Development of Ni-Base Superalloy with Operating Temperature up to 800°C for Gas Turbine Disks

M. M. Bakradze, S. V. Ovsepyan, A. A. Buiakina and B. S. Lomberg p. 1044 abstract

Influence of Hot Plastic Deformation Modes on the Structure and Properties of Quenched Hot Rolled Economically Alloyed High-Strength Steel

U. A. Pazilova, E. I. Khlusova and T. V. Kniaziuk p. 1051 abstract

Structure Formation of the Nitrogen-Containing Austenitic 04Kh20N6G11M2AFB Steel at Hot Deformation: Part I. Influence of Deformation Temperature and Strain Rate on the Process of Dynamic Recrystallization

O. V. Fomina, T. V. Vikhareva, V. V. Sagaradze and N. V. Kataeva p. 1060 abstract

Structure Formation of the Nitrogen-Containing Austenitic 04Kh20N6G11M2AFB Steel at Hot Deformation: Part II. Influence of the Phase Composition and Conditions of Hot Deformation on the Process of Dynamic Recrystallization

O. V. Fomina and T. V. Vikhareva p. 1070 abstract

Structure and Properties of the Heat-Affected Zone of Low-Alloy Cold-Resistant Steel for Arctic Application

O. V. Sych, E. I. Khlusova, U. A. Pazilova and E. A. Yashina p. 1076 abstract

Functional Materials

Features of Thermal Effects of Coatings Fabricated by Cold Gas Dynamic Spraying under Thermal Load

D. A. Gerashchenkov and A. Yu. Askinazi p. 1090 abstract

Wear- and Corrosion-Resistant Functionally Gradient Coatings Based on Composite Powders of Metal–Nonmetal System

T. I. Bobkova and B. V. Farmakovsky p. 1096 abstract

Cast Microwire with High Value of Thermoelectromotive Force

B. V. Farmakovsky p. 1100 abstract

Polymer Composite Materials

Heat-Resistant Electrical Insulating Fiberglass Plastics for Shipbuilding

V. E. Bakhareva, I. V. Nikitina, A. S. Sargsian, V. F. Aristov and I. A. Vikhrov p. 1103 abstract

Epoxy Vinyl Ester Binder for Fire-Resistant Marine Fiberglass Plastics

A. V. Anisimov, V. S. Tryasunov, E. L. Shultceva, Ju. V. Sokolov and F. V. Mudry p. 1116 abstract

Researching the Interface of Polymer Matrices with Optical Fibers in Smart Materials

M. Yu. Fedotov, A. M. Shienok, R. R. Mukhametov and I. N. Gulyaev p. 1123 abstract

Temperature and Frequency Dependences of Dissipative Properties of Rigid Vibration-Damping Coatings

V. L. Lebedev, V. Yu. Kosulnikov, P. V. Seryi, N. N. Vasilieva and A. A. Logunova p. 1132 abstract

Welding and Allied Processes. Welding Consumables and Technologies

Improvement of the Service Properties of the Weld Joint Metal for Transport Nuclear Power Units Manufactured of Heat-Resistant Steel Grades: Part I. Technology of Welding Heat-Resistant Steel Grades Using Low-Carbon Welding Materials without Heat Treatment and Experience of Applying Welding Materials

M. N. Timofeev, G. P. Karzov, S. N. Galiatkin, E. I. Mikhaleva, S. G. Litvinov, A. G. Aleksandrin, D. L. Bashulin and O. V. Shubin p. 1142 abstract

Improvement of the Service Properties of the Weld Joint Metal for Transport Nuclear Power Units Manufactured of Heat-Resistant Steel Grades: Part II. A Study of Mechanical Properties of Low-Carbon Weld Deposits Depending on the Welding Process Variables

M. N. Timofeev, S. N. Galiatkin, E. I. Mikhaleva and O. V. Shubin p. 1148 abstract

Improvement of the Service Properties of the Weld Joint Metal for Transport Nuclear Power Units Manufactured of Heat-Resistant Steel Grades: Part III. A Study of the Influence of Alloying Elements on the Characteristics of the All-Weld Metal as Applied to the Fabrication of Low-Carbon Metal Deposits and Assembly Weld Joints in Icebreaker Nuclear Power Units

M. N. Timofeev, S. N. Galiatkin and E. I. Mikhaleva p. 1155 abstract

Effect of Boron Microalloying on the Structure and Properties of a Welded Joint Made of a Flux-Cored Wire for Welding of Flat-Rolled High-Strength Steel Plates with a Standard Yield Stress of 750 MPa

P. V. Melnikov, V. V. Gezha, G. D. Motovilina and V. A. Mogilnikov p. 1165 abstract

Calculation of Thermal Processes around Moving Molten Pool Using Boundary Element Method

V. A. Karkhin, P. N. Khomich, O. V. Panchenko and S. Yu. Ivanov p. 1169 abstract

Corrosion and Protection of Metals

Effect of Interstitial Elements on Pitting and Intercrystalline Corrosion of Austenitic Chromium-Nickel Steel

A. S. Kudriavtsev, K. A. Okhapkin and S. A. Suvorov p. 1175 abstract

Some Aspects of Studying the Corrosion Processes in 25Kh1MF Steel Fasteners after Aluminizing

M. I. Olenin, V. I. Gorynin, B. I. Berezhko, I. M. Khovratovich and A. V. Ptashnik p. 1182 abstract

Radiation Materials Science

Synergistic Mechanism of Radiation Embrittlement of Austenitic Stainless Steels under Long-Term High-Temperature Irradiation

V. A. Shvetsova, O. Yu. Prokoshev, B. Z. Margolin, A. A. Sorokin and V. A. Potapova p. 1188 abstract

Influence of Neutron Irradiation and Post-Irradiation Annealing on Mechanical Properties and Fracture Toughness of the Anticorrosive Cladding for VVER-Type Reactors: Part 1. Mechanisms of Embrittlement and Recovery of Cladding Properties

B. Z. Margolin, A. M. Morozov, A. Ya. Varovin, V. I. Kostylev, L. A. Belyaeva, V. A. Potapova, V. I. Smirnov, O. Yu. Prokoshev and S. N. Petrov p. 1198 abstract

Influence of Neutron Irradiation and Post-Irradiation Annealing on Mechanical Properties and Fracture Toughness of Anticorrosive Cladding for VVER-Type Reactors: Part 2. Predictive Modeling of the Mechanical Properties and Fracture Toughness of Cladding

B. Z. Margolin, V. I. Kostylev, A. M. Morozov, A. Ya. Varovin, L. A. Belyaeva, V. A. Potapova, V. I. Smirnov, O. Yu. Prokoshev and S. N. Petrov p. 1210 abstract

Study of Steel Corrosion Cracking Mechanisms for VVER RPV Internals Based on Simulation Tests

B. Z. Margolin, N. E. Pirogova, V. A. Potapova, A. A. Sorokin, N. V. Bardashova, S. N. Petrov and M. S. Mikhailov p. 1221 abstract

Improvement of the Approach to Predict the Fracture Toughness of Irradiated Anticorrosive Cladding for WWER-Type Reactors

A. J. Minkin, A. M. Morozov and V. I. Smirnov p. 1237 abstract

Simulation of Materials and Technological Processes

Mathematical Modeling of Stress–Strain State in Titanium Alloys Considering the Microstructure and Crystal Orientation Measured by EBSD

A. Yu. Musienko, V. P. Leonov, I. R. Kozlova and S. N. Petrov p. 1243 abstract

Structural and Technological Strength and Efficiency of Materials

Construction of Theoretical Curves of the Long-Term Strength for Neutron-Irradiated Austenitic Steels Kh18N9 and 08Kh16N11M3

A. G. Gulenko, B. Z. Margolin, A. A. Buchatskii and A. A. Nuzhdov p. 1254 abstract

Contents